Hardtop Type: 1-Piece Removable Hardtop with Half-Door Insert
Truck Model: Jeep Wrangler TJ (1997-2006)

General Safety Information:

Instructions – Safety

Your hardtop will come with all the necessary parts to complete your installation. To safely lift and install this hardtop, you will need the assistance of at least one other person. The following instructions are examples of the installation. Please follow the instructions that are included with your hardtop.

REMEMBER: It is the owner’s responsibility to insure proper installation and perform monthly maintenance checks of fasteners. Doing so will assure safe operation and long life of your upper hard doors.

Instructions – Warning

WARNING: The top on this vehicle is designed only for additional protection against the elements. Do not rely on the top to contain occupants within the vehicle or to protect against intrusion of foreign objects, nor injury during an accident. Make sure all brackets and screws are tight. Periodically check for tightness and retighten when necessary. Wear seat belts at all times.

Parts Provided (Hardtop):

  • 6 each – Bolt 5/16 x 18 x 1 1/4
  • 6 each – Nut 5/16 x 18
  • 6 each – Washer 5/16
  • Instruction sheet

Parts Provided (Half-Door):

  • 2 each — 3/8″ x 4.5″ Button head bolts – uses 7/32 allen wrench
  • 4 each — 3/8″ x 5.0″ Button head bolts – uses 7/32 allen wrench
  • 6 each — 3/8″ Nylon washers
  • 6 each — 3/8″ Steel washers
  • 6 each — Door inserts
  • 1 each — Left upper half door
  • 1 each — Right upper half door
  • Instruction sheet


Follow the instructions and perform the steps in the sequence given. Shortcuts to the directions may result in an unsatisfactory installation.


1. Unzip side windows and remove.

2. Unzip rear window and remove.

3. Pull back bar to disengage and remove.

4. Pull down on corners and remove.

5. Pry open side connections with screwdriver.

6. Remove side connections to door frame.

7. Disengage soft top from windshield.

8. Pull back soft top.

9. Remove bolt from soft top frame.

10. Pry off soft top frame from roll bar.

11. Remove soft top.

12. Unscrew door pins & remove frames.

13. Remove rear bar holders.

14. See pre-installation instruction sheet.

15. Do not remove end seal.

16. Install hardtop on vehicle with at least 2 people.

17. Install 6 bolts with washers using nut plates.

18. Adjust the cam locks to medium tension..

You’re Done! Enjoy!


Before you tighten down the flange bolts make sure the top is centered on the windshield. Make sure the top is equal distance in both corners.

Sit in the front seat and look up at the windshield. Make sure the windshield stop is not hug up on the molding. It should look like this.

Check to make sure the clearance between the door and the top looks like this. Too close will pinch the door seal. Too much clearance will cause air leakage.


1. Remove the soft upper half doors. Remove the factory installed Jeep door inserts by using a large flat-bladed screw driver and gently prying them up.

2. Easily removed by hand. There should be three (3) per side. (Please note the positioning of the Jeep Door Inserts before removal. The flange of the inserts must be rotated correctly in order for the inserts to sit flush with the door when reinstalled)

3. Install the new door inserts back into the lower door holes. There is a tab on one side of the insert, it can only fit into the hole in one direction. If the inserts are installed properly, the top plastic flange will rest against the top portion of the door.

4. Place the metal washer first and then the plastic washer onto the bolts. Place the upper half door onto the lower half door. Insert the bolts, 4.5″ bolt in the front and the 5.0″ bolts in the back two holes.

As you tighten the bolts, from the top of the insert, pull in, until they are snug. DO NOT OVER TIGHTEN.

Need more help?

Installing your hardtop sport truck hardtop is a simple process, but we are always ready to lend expert advice.

Contact Us